|
|
||||||||
From the 1 From the Departments of Neurology, Case Western Reserve University and 2 Cleveland Veterans Affairs Medical Center, Cleveland, Ohio.
| Abstract |
|---|
|
|
|---|
METHODS. A device was developed that senses eye movements and, by the use of motor-driven prisms, oscillates the image of the world in lockstep with the pathologic nystagmus, to negate its deleterious visual effects. Unlike existing optical and surgical treatments for nystagmus, the device negates only the pathologic movements. Voluntary and normal reflex eye movements required for normal vision are unaffected. The benefits of the device were assessed by its impact on acuity in five patients with medication-refractory APN.
RESULTS. All patients reported decreases in oscillopsia when the device was in operation. Averaged across patients, the device increased the percentage of time in which retinal image velocity was within ±4°/sec from 12.8% to 33.3%. Acuities improved in four of five patients, by an average of 0.21 logMAR units.
CONCLUSIONS. The symptoms of pendular nystagmus can be treated with a servomechanical device. Further refinements in the device should result in greater improvements in acuity, and a portable, wearable version is feasible using existing technologies.
| Introduction |
|---|
|
|
|---|
In the laboratory setting, acuity can be enhanced and oscillopsia prevented if the visual target (for instance, an acuity chart) is oscillated in lockstep with an APN patients ocular oscillations.5 This observation suggests a new way to treat APN through a goggles-mounted device that senses the patients ocular oscillations and optically translates the image of the world, to stabilize the image on the moving retina. Using a prototype table-mounted device, we explored the feasibility of such an electromechanicaloptical treatment for medication-refractory patients with APN. Preliminary results have been reported.6
| Methods |
|---|
|
|
|---|
Device Electronics and Optics
The prototype device is capable of correcting vertical and
horizontal sinusoidal oscillations in one eye. Its basic elements
include a head-mounted eye positionsensing device; table-mounted,
motor-driven prisms that allow the image of the world (as viewed
through the prisms) to be shifted left-right and up-down; and an
electronics package that uses the eye movement signals to control the
prism motors. One of the authors models the device in Figure 1
.
|
Figure 2 shows a simplified block diagram of the device electronics. The circuit can be driven by either the horizontal or vertical eye movement channel. In practice, we selected whichever channel carried the strongest pendular nystagmus signal. The input eye position signal is differentiated (D/DT) and fed to a phase-locked loop, an oscillator that generates an unmodulated (constant amplitude), quasi-sinusoidal signal with frequency and phase that are locked to the patients sinusoidal nystagmus. The phase-locked loop is configured to lock to any oscillation in the approximate range of 2 to 10 Hz, with an acquisition time of two to three cycles. The loops low-pass characteristics guarantee that momentary transients in the eye velocity signal (e.g., from small saccades) are not tracked. Likewise, slow eye movements related to the vestibulo-ocular reflex or smooth pursuit have essentially no effect on the output of the phase-locked loop. After the phase-locked loop circuitry, the control of vertical and horizontal movement channels of the device diverges. For each plane, the signal passes through an adjustable phase-shift network, which allows the phase of the prism motion to be adjusted to perfectly match the patients oscillation. The phase-shifted signals are then fed to sign detection and absolute-value circuits, the outputs from which, respectively, supply the direction and speed commands to stepper motor controllers. Angular position of the prisms (which is transduced by potentiometers mechanically coupled to the motor shafts) is low-pass filtered (fc = 0.8 Hz) and fed back to the control circuitry. The sign of this position feedback is contrived so that the circuit maintains average prism position centered at the point where angular deflection of the world (seen through the prisms) is nil.
|
After passing through low-pass Bessel filters (corner frequency, 100 Hz), eye and prism position signals are digitized at 200 Hz with 16-bit resolution and recorded on a computer. Prism position signals are scaled to reflect the angular deflection of the world, as viewed though the prisms. The scale factor was determined by passing a laser beam through the prism assemblies, converting the linear displacement of the beam to angular displacement, and then correlating these angles with the amplitude of the position feedback signal.
Selection of Correction Axis and System Alignment
Although the prototype device is capable of simultaneously
correcting both horizontal and vertical components of APN, in practice
we corrected oscillations in one plane only (see the Discussion
section). For each patient we chose the eye and treatment plane based
on a number of considerations, seeking to study the eye in which the
oscillations were most pronounced, most sinusoidal (i.e., minimally
distorted by other motions such as superimposed jerk nystagmus), and
closest to pure horizontal or vertical. We also wanted to avoid
studying an eye that had severe degradation of vision due to
concomitant optic nerve disease, although mild to moderate reduction of
acuity due to optic nerve disease or refractive errors (patients did
not wear correction during testing) should not affect the results,
because they are based on the change of acuity produced by
the device.
All eye movement calibrations and acuity determinations were performed as the patient viewed through the prism optics. The devices limited field of view required patients to restrict their head movements during testing. However, their heads were not restrained, and small head movements with consequent compensatory eye movements occurred. Throughout the testing, the untreated eye was patched. Vertical and horizontal calibrations were determined as the patient foveated targets at known angular positions. After calibration, the system phase was adjusted so that the prism and eye oscillations, as viewed on an oscilloscope, were in perfect registration. Next, the amplitude of the prism oscillation was adjusted in an iterative process until the patient reported optimum stability of the visual world.
Acuity Testing
After completion of the adjustment procedure described, the effect
of the device was determined objectively by comparing patients
acuities with the device switched on or off. Acuity was tested using
four-position, black-on-white Landolt C optotypes. Two different
methods were used to present the optotypes. For subjects 2 and 4 and
session 1 of subject 1, the optotypes were presented on cards,
positioned 440 mm from the patients eye. For subjects 3 and 5 and
session 2 of subject 1, optotypes were displayed on the screen of a
laptop computer (Powerpoint; Microsoft, Redmond, WA), positioned at
distances of 120 to 150 cm from the patient. Twenty black optotypes of
each size were presented on a white background, each for 3 seconds,
with a fade-through-black transition between successive optotypes. For
both methods of acuity testing, optotypes were converted to decimal
acuity (taking into account the viewing distance), and the percentage
of correct responses was scored.
Some patients with APN can temporarily attenuate the nystagmus by blinking, squinting, or making saccades.7 Where applicable, patients were instructed to avoid these volitional maneuvers during acuity testing. Acuity testing can still be confounded in patients with APN because momentary attenuations of the nystagmus may still occur, allowing a patient to resolve an occasional optotype, particularly if each optotype is displayed for a prolonged time. These spurious correct responses make it difficult to assign a numerical acuity. The computerized optotype presentation was designed to reduce this problem in several ways: Each optotype was visible for only a short period (reducing the chance of a nystagmus arrest occurring), large numbers of optotypes were displayed (reducing the statistical effect of an occasional nystagmus arrest), optotypes were presented at a fixed position (obviating the need for foveating saccades that might induce a nystagmus arrest), and the gradual transition between optotypes eliminated temporal edges that might assist the patient in overcoming the blurring effect of the nystagmus.
Data Analysis
The frequency and amplitude of ocular and world (as viewed through
the device) oscillations were determined by fitting sine waves to
successive 1-second epochs of the record and the resultant frequencies
and amplitudes averaged. Any epochs that generated spurious fits (due,
for instance, to a saccade-associated shift in nystagmus phase
occurring within the analysis epoch) were discarded. All saccades,
blinks, and temporary cessations of nystagmus (generally occurring
after blinks) were deleted before curve fitting.
| Results |
|---|
|
|
|---|
Figure 3 shows a 2-second segment of ocular oscillations in patient 1, recorded with the device in operation. In the absence of the device, the patient would experience a retinal slip velocity equal and opposite to her eye velocity. With the device in operation, the patient experienced only a residual image velocity (bottom trace), which was calculated from the difference between eye velocity and angular velocity of the world imparted by the movement of the prisms. Comparison of the eye and residual image velocity traces demonstrates how the device reduced peak-to-peak retinal image velocity by more than 50%. The record contains two small saccades, which had no effect on the ocular oscillation. Likewise, the prism oscillation was unaffected. This state of affairs is desirable, because the device should counter only the involuntary oscillations.
|
|
|
|
| Discussion |
|---|
|
|
|---|
Although the prototype device is table mounted, most of the elements can be miniaturized easily, suggesting that a portable, wearable, battery-operated device could be developed. The infrared eye movement sensor is already battery powered, operates under any lighting conditions, and has circuitry that fits in a small box that could be worn by the patient on a belt. The prism-control electronics would fit easily in the same box and run from the same power source. Only the motor-operated prisms present a problem, because of their weight, power requirements, and need for bulky heat sinks. However, the problem could be solved by replacing the motor-driven Risley prisms by variable power prisms such as those used in stabilized binoculars (e.g., Vari-Angle prisms, Canon, Lake Success, NY). These assemblies are light, quiet, and operate from battery power. The variable prism is also more compact (longitudinally) than the Risley configuration and thus would allow a larger field of view for any given prism diameter.
The device should be operable by a patient without assistance. For the purposes of these experiments, it was important to obtain interpretable eye movement recordings, and thus the IR probe had to be positioned correctly and calibrated. However, in practice, no calibration would be performed, and alignment would be noncritical, because all that is required is a nystagmus signal of sufficient quality for the circuitry to achieve phase lock. Because nystagmus amplitude varies through the day, the patient would need to readjust the vertical and horizontal prism amplitudes periodically to maintain the preferred system gain. However, because the phase relationships between vertical and horizontal nystagmus components tend to remain stable from day-to-day in a given patient, the system phase controls would need only periodic adjustments, which may be performed in a physicians office.
Deficiencies of the Prototype Device
These experiments have identified a number of deficiencies in the
prototype device that could be corrected, possibly leading to greater
improvements in efficacy. The field of view was quite limited,
subtending only 10° of arc. As noted, the field of view could be
enlarged somewhat by using a more compact prism device. In addition,
the constraints of the small field of view would be considerably
mitigated by a head-mounted device. Based on the literature on
adaptation to aperture goggles, we anticipate that patients would
rapidly learn to substitute eyehead saccades for eye-only saccades,
thereby maintaining visual targets within the field of
view.12
13
14
Another deficiency of the prototype is apparent in Figure 3 , in which it is clear that the velocity profile of the prisms is more triangular than sinusoidal; subtraction of this waveform from the more perfectly sinusoidal ocular oscillation produces a residual image velocity waveform with prominent ripples. As the device gain was increased toward 1.0, these ripples became apparent to subjects as a high-frequency jitter in the image and probably account for most patients preferring a device gain significantly less than 1.0. The distortions stem from several sources, including mechanical backlash in the Risley prism gears and nonlinearities contributed by the behaviors of the absolute-value circuit around 0 volts, the simple resistorcapacitor phase-delay network, and the limited speed resolution of the stepper motor controller. Modifications to the system to increase the fidelity with which it mirrors eye velocity would reduce this jitter and may allow higher gains. The tracking inaccuracy may also explain why operating both prism axes simultaneously did not improve vision in patients with prominently circularelliptical nystagmus (e.g., patients 2, 4, 5). Summation of the high-frequency errors from both axes would generate a complex two-dimensional jitter with high-image velocities. If tracking fidelity were improved, we should be able to operate both axes, again with potential for further improvements in efficacy. A third, rectifiable deficiency of the prototype was that it had no provision to disable its oscillation when it was out of lock. Thus, during transient losses of lock due to blinks, large saccades, or nystagmus arrests, the prisms continued to oscillate and actually increased retinal slip velocities. Disabling prism oscillation during these moments should improve measured acuities somewhat. A fourth deficiency of the device was that it did not permit patients to wear their optical correction. A practical device would be designed to incorporate the patients optical prescription.
Experience with the prototype also revealed problems that will render challenging the creation of practical, wearable APN-nullifying goggles. First, the circuitry required several unbroken cycles of nystagmus to acquire complete phase lock. In some patients the pendular oscillation was constantly interrupted by blinks, saccades, and jerk nystagmus, and the percentage of in-lock time was reduced. Second, in some patients (e.g., patient 2), the nystagmus amplitude varied constantly. To maintain consistent compensation for the ocular oscillation, the current prism-control circuitry would require continuous amplitude adjustments. Both these problems could be addressed by replacing the phase-locked loop circuit with a more sophisticated predictive tracking mechanism, probably based on microprocessor and digital signal processor technology. A more sophisticated circuit could also adjust for changes in nystagmus amplitude, thus maintaining a consistent system gain. The need for this and other refinements must be clarified during testing of a head-mounted prototype. Other issues that should be considered in developing a practical treatment include the degree to which the device tolerates compensatory eye movements, the design and usability of any patient-operated controls, and the mean time to failure under realistic conditions of use.
Implications for Treating Disorders of Eye Movements in General
Acquired pendular nystagmus is only one of several disorders of
eye movements that impair vision.2
We chose to design a
device to treat APN, because the characteristics of the nystagmus
waveform are simple, and thus relatively simple circuitry sufficed to
detect and selectively negate the ocular oscillations. With more
sophisticated control circuitry, the general approach of using
servo-controlled prisms to shift the image of the world could be used
to treat nonsinusoidal ocular oscillations (i.e., jerk nystagmus),
acquired strabismus, and, with the addition of a head movement sensor,
vestibular insufficiency.
| Acknowledgements |
|---|
| Footnotes |
|---|
Submitted for publication July 12, 1999; revised October 21, 1999; accepted October 27, 1999.
Commercial relationships policy: C3(JSS).
Corresponding author: John S. Stahl, Dept of Neurology, University Hospitals of Cleveland, 11100 Euclid Avenue, Cleveland, OH 44106. jss6{at}po.cwru.edu
| References |
|---|
|
|
|---|
This article has been cited by other articles:
![]() |
J. B. Jacobs, L. F. Dell'Osso, R. W. Hertle, G. M. Acland, and J. Bennett Eye Movement Recordings as an Effectiveness Indicator of Gene Therapy in RPE65-Deficient Canines: Implications for the Ocular Motor System. Invest. Ophthalmol. Vis. Sci., July 1, 2006; 47(7): 2865 - 2875. [Abstract] [Full Text] [PDF] |
||||
![]() |
J. S Stahl, G. T Plant, and R J. Leigh Medical treatment of nystagmus and its visual consequences J R Soc Med, January 5, 2002; 95(5): 235 - 237. [Full Text] [PDF] |
||||
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| HOME | HELP | FEEDBACK | SUBSCRIPTIONS | ARCHIVE | SEARCH | TABLE OF CONTENTS |